• APC BR550GI Power-Saving Back-UPS Pro 550

APC Back-UPS Pro, 330 Watts / 550 VA, Input 230V / Output 230V , Interface Port DB-9 RS-232, USB

Features

Green mode
Patent-pending operating mode that bypasses unused electrical components in good power conditions to achieve very high operating efficiency without sacrificing any protection.

Battery failure notification
Provides early-warning fault analysis on batteries enabling timely preventive maintenance

Power-saving outlets
Automatically cuts power to idle equipment to conserve electricity.

Battery-protected and surge-only outlets
Reserves power capacity and run time for connected equipment that require UPS battery back-up while providing surge only protection for less critical equipment

Cold-start capable
Provides temporary battery power when the utility power is out.

Hot-swappable batteries
Ensures clean, uninterrupted power to protected equipment while batteries are being replaced

Disconnected battery notification
Warns when a battery is not available to provide backup power.

Dataline Surge Protection
Provides protection of connected equipment from power surges on the data lines.

Automatic self-test
Periodic battery self-test ensures early detection of a battery that needs to be replaced.

Audible alarms
Provides notification of changing utility power and UPS power conditions

User-replaceable batteries
Increases availability by allowing a trained user to perform upgrades and replacements of the batteries reducing Mean Time to Repair (MTTR)

USB connectivity
Provides management of the UPS via a USB port (not available on all models).

Boost and Trim Automatic Voltage Regulation (AVR)
Gives higher application availability by correcting low and high voltage conditions without using the battery (not available on all models).

Safety-agency approved
Ensures the product has been tested and approved to work safely with the connected service provider equipment and within the specified environment.

Battery replacement without tools
Enables fast battery replacement, lowering Mean Time to Repair (MTTR).

LCD graphics display
Text and mimic diagrams that display modes of operation, system parameters and alarms.

Automatic Voltage Regulation (AVR)
Automatically steps up low voltage and steps down high voltage to levels that are suitable for your equipment.

Protection

Battery and surge protected outlets
Back up and protect your hardware and data during power outages, surges and spikes.

Dataline Surge Protection
Provides protection of connected equipment from power surges on the data lines.

Surge only outlets
Protect secondary electronics from surges and spikes without reducing battery power used to run primary electronics during an outage.

Availability

Energy Management Function
Energy saving feature automatically power off peripherals when the a master device, usually a PC, hibernates or is shut down. Power to peripherals is immediately restored when the master device wakes up or is switched on.

Boost and Trim Automatic Voltage Regulation (AVR)
Gives higher application availability by correcting low and high voltage conditions without using the battery (not available on all models).

Green mode
Patent-pending operating mode that bypasses unused electrical components in good power conditions to achieve very high operating efficiency without sacrificing any protection.

Customizable voltage-transfer points
Adjust the voltage points (widen or tighten the range) where your UPS transfers to battery to maximize useful battery life and protect sensitive electronics.

Customizable voltage sensitivity
Toggle between pre-determined voltage-transfer points depending on your power quality (high, medium or low sensitivity), maximizing useful battery life and protecting sensitive electronics.

Intelligent battery management
Maximizes battery performance, life, and reliability through intelligent, precision charging.

Cold-start capable
Provides temporary battery power when the utility power is out.

Battery failure notification
Provides early-warning fault analysis on batteries enabling timely preventive maintenance

Automatic self-test
Periodic battery self-test ensures early detection of a battery that needs to be replaced.

Transformer-block spaced outlets
Protect equipment with input transformer blocks without blocking access to other receptacles.

Serviceability

Resettable circuit breaker
Easy recovery from overloads; no need to replace a fuse.

Simple battery replacement
Increases UPS availability by allowing quick, easy battery replacement.

Manageability

USB connection
Use your PC to access additional power protection and management features for your UPS via a USB Port.

LCD Status Display
Provides key UPS status at a glance. Multiple status indicators with load and battery bar graphs.

Audible alarms
Provides notification of changing utility power and UPS power conditions

Disconnected battery notification
Warns when a battery is not available to provide backup power.

Safety

Safety-agency approved
Ensures the product has been tested and approved to work safely with the connected service provider equipment and within the specified environment.

Specification

Output
Output Power Capacity 330 Watts / 550 VA
Max Configurable Power 330 Watts / 0 VA
Nominal Output Voltage 230V
Efficiency at Full Load 77.0%
Output Frequency (sync to mains) 50 Hz
Topology Line Interactive
Waveform Type Stepped approximation to a sinewave
Output Connections (3) IEC 320 C13 (Battery Backup)
(3) IEC 320 C13 (Surge Protection)
(2) IEC Jumpers (Battery Backup)
Efficiency at Half Load 84.0%
Input
Nominal Input Voltage 230V
Input Frequency 50/60 Hz +/- 3 Hz (auto sensing)
Input Connections IEC-320 C14
Input voltage range for main operations 176 - 282V
Input voltage adjustable range for mains operation 155 - 290V
Maximum Input Current 6A
Input Breaker Capacity
7.0  A
Batteries & Runtime
Battery Type Maintenance-free sealed Lead-Acid battery with suspended electrolyte : leakproof
Typical recharge time 12 hour(s)
Replacement Battery APCRBC110
RBC™ Quantity 1
Communications & Management
Interface Port(s) DB-9 RS-232, USB
Control panel
Multi-function LCD status and control console
Audible Alarm Alarm when on battery : distinctive low battery alarm : overload continuous tone alarm
Surge Protection and Filtering
Surge energy rating 420 Joules
Filtering Full time multi-pole noise filtering :10% of IEEE surge let-thgouh : zero clamping response time: instantaneous
Data Line Protection Network line - 10/100/1000 Base-T Ethernet (RJ-45 connector)
Physical
Maximum Height 190.00 mm
Maximum Width 91.00 mm
Maximum Depth 310.00 mm
Net Weight 6.53 KG
Shipping Weight 7.71 KG
Shipping Height 252.00 mm
Shipping Width 138.00 mm
Shipping Depth 442.00 mm
Master Carton Units 2.00
Master Carton Weight 15.94 KG
Color Black
SCC Codes 1073130426688 1
Units per Pallet 48.00
Environmental
Operating Environment
0 - 40 °C
Operating Relative Humidity 0 - 95%
Operating Elevation 0-3000 meters
Storage Temperature -15 - 45 °C
Storage Relative Humidity 0 - 95%
Storage Elevation 0-15000 meters
Audible noise at 1 meter from surface of unit 45.00 dBA
Conformance
Regulatory Approvals A-tick, C-tick, CE, GOST, GS Mark
Standard Warranty 2 years repair or replace, 3 years repair or replace for European Union countries
Equipment protection policy Lifetime : 200000 AUD, Lifetime : 150000 Euros, Lifetime : 75000 GBP
Sustainable Offer Status
RoHS Compliant
REACH REACH: Contains No SVHCs

Includes: CD with software, USB cable, User Manual, Warranty card  


*Box quantity refers to the number of units contained in this product's outer packaging. It does not refer to the number of products purchased for the quoted unit price unless otherwise stated.

Write a review

Please login or register to review

APC BR550GI Power-Saving Back-UPS Pro 550

  • Brand: APC
  • Product Code: APC BR550GI Power-Saving
  • Availability: In Stock Ships in 1-2 days
  • $170.00



Are you a VAR / Distributor?
Up to 15% Commission.
No MOQs. No Signup Fees.

Tags: apc, br550gi, power, saving, back, ups, pro, 550



Featured Article

Portable Server Room Diagnostic Sensor Toolkit

Despite advances in CFD software and pre-deployment simulations of data center environments. The majority of server rooms, remote sites and data centers are not designed to handle ever increasing loads and the heat generated by that increased activity.

WIRELESS WORKFLOW enables early diagnostics of any server room or data center facility. Detecting problems arising from under or over cooling, hot air re-circulation in IT rack space and air delivery resulting in high or low air pressure in raised floors and dropped ceiling plenums.

Read the full article

Diagnosing server room temperature problems

Diagnose temperature differentials, pressure differentials and more...


AVTECH Room Alert 12E - Sensor Monitoring

Monitor temperature, humidity, power, room access and more...


AKCP SP2+ Temperature Monitoring

SP2+ monitors and logs temperature, humidity and more. SNMPv3 compliant, encrypted email and more...

Smart Cooling for Data Centers

Keeping temperatures in ASHRAE safe thermal envelopes.


AKCP SP2+ Temperature Sensor for Server Rooms

Front and rear thermal mapping for any server cabinet.


NTI Enviromux Micro-T SNMP Temperature Sensor

Monitor and manage server room environmental and security conditions over an IP network.


CTSI Limited - Complete Technology Systems Integration

At CTSI we've worked with some of the largest companies in the world, bringing our expertise to bear on many complex server room monitoring projects. Feel free to contact us today at sales@ctsilimited.com and make your project a success.