APC MGE Galaxy 3500 10kVA 400V with 1 Battery Module Expandable to 2, Start-up 5X8
APC MGE Galaxy 3500,8000 Watts /10 kVA,Input 400V 3PH /Output 400V 3PH, Interface Port DB-9 RS-232, G35T, Extended runtime model
Dual mains input
Increases availability by allowing the UPS to be connected to two separate power sources.
Ensures clean, uninterrupted power to protected equipment while batteries are being replaced
Increases total power capacity by using multiple uninterruptible power supplies simultaneously.
Advanced electrical features
Excellent power conditioning, very low harmonic distortion through IGBT rectifier, input power factor correction, and high power efficiency
Frequency and voltage regulation
Gives higher application availability by correcting poor frequency and voltage conditions without using the battery.
Automatic internal bypass
Supplies utility power to the connected loads in the event of a UPS power overload or fault.
Ensures clean, uninterrupted power to protected equipment when generator power is used.
Simplifies installation and UPS maintenance while minimizing space requirements.
User-replaceable air filters
Enables quick and simple replacement of air filters.
Battery replacement without tools
Enables fast battery replacement, lowering Mean Time to Repair (MTTR).
Multiple levels of service
With the option of packages or individual service components, our services are structured to allow you to pick and choose what you would like APC to do for you.
7x24 telephone technical support
Our experienced technical support engineers are available to answer your questions, giving you peace of mind knowing the help you need is there when you need it.
Built-in Web/SNMP management
Full-featured management via a Web browser as well as comprehensive management from a Network Management System.
Prevent equipment failure from a full range of threatening environmental conditions.
LCD graphics display
Text and mimic diagrams that display modes of operation, system parameters and alarms.
Provides notification of changing utility power and UPS power conditions
Total Cost of Ownership
Input power factor correction
Minimizes installation costs by enabling the use of smaller generators and cabling.
Small UPS footprint provides maximum usage of valuable electrical room floorspace
Temperature-compensated battery charging
Prolongs battery life by regulating the charge voltage according to battery temperature.
|Output Power Capacity|| |
8000 Watts / 10 kVA
|Max Configurable Power|| |
8000 Watts / 10 kVA
|Nominal Output Voltage||400V 3PH|
|Output Voltage Note||Configurable for 380 : 400 or 415 V 3 Phase nominal output voltage|
|Efficiency at Full Load||95.7%|
|Output Voltage Distortion||Less than 5%|
|Output Frequency (sync to mains)||47 - 53 Hz for 50 Hz nominal|
|Other Output Voltages||380, 415|
|Topology||Double Conversion Online|
|Waveform Type||Sine wave|
|Output Connections||(1) Hard Wire 4-wire (3PH + G) |
(1) Hard Wire 5-wire (3PH + N + G)
(1) Screw Terminals
|Output Voltage Tolerance||+/-1% static and +/- 5% at 100% load step|
|Output Voltage THD||< 2% for 0 to 100% linear load and < 5% for full non linear load|
|Overload Operation|| |
10 minutes @ 125% and 60 seconds @ 150%
|Efficiency at Half Load||95.2%|
|Bypass||Built-in Maintenance Bypass, Built-in Static Bypass|
|Nominal Input Voltage|| |
|Input Frequency||40 - 70 Hz (auto sensin|
|Input Connections||Hard Wire 5-wire (3PH + N + G)|
|Input voltage range for main operations||304 - 477V|
|Input voltage adjustable range for mains operation||340 - 460 (400V)V|
|Other Input Voltages|| |
|Maximum Input Current||14A|
|Input Breaker Capacity||16 A|
|Input Total Harmonic Distortion||Less than 5% for full load|
|Type of Input Protection Required||3-pole breaker|
|Batteries & Runtime|
|Battery Type||Maintenance-free sealed Lead-Acid battery with suspended electrolyte : leakproof|
|Included Battery Modules||1|
|Available Battery Module Slots||1|
|Typical recharge time||5 hour(s)|
|Nominal Battery Voltage||+/-192 V (split battery referenced to neutral)|
|End of Discharge Battery Voltage||+/-154 V|
|Efficiency in Battery Operation||94.10%|
|End of Discharge Maximum Battery Current||109|
|Overload Operation||10 minutes @ 125% and 60 seconds @ 150%|
|Extended Run Options|
|Communications & Management|
|Interface Port(s)|| |
DB-9 RS-232, G35T
|Pre-Installed SmartSlot™ Cards||AP9631|
|Control panel|| |
Multi-function LCD status and control console
|Audible Alarm||Alarm when on battery : distinctive low battery alarm : configurable delays|
|Emergency Power Off (EPO)||Yes|
|Maximum Height||1491.00 mm|
|Maximum Width||352.00 mm|
|Maximum Depth||838.00 mm|
|Net Weight||214.00 KG|
|Shipping Weight||245.00 KG|
|Shipping Height||1643.00 mm|
|Shipping Width||650.00 mm|
|Shipping Depth||1062.00 mm|
|Operating Environment||0 - 40 °C|
|Operating Relative Humidity|| |
0 - 95%
|Operating Elevation|| |
|Storage Temperature||-15 - 45 °C|
|Storage Relative Humidity|| |
0 - 95%
|Storage Elevation|| |
|Audible noise at 1 meter from surface of unit||51.30 dBA|
|Online Thermal Dissipation||1501.00 BTU/hr|
|Protection Class|| |
|Regulatory Approvals||CE, EN 50091-2, EN/IEC 62040-3, EN/IEC 62040-1-1, IEC 61000-3-2, IEC 61000-3-3, ISO 14001, ISO 9001, VFI-SS-111|
|Standard Warranty||1 year repair or replace|
Includes: Battery modules ship installed, Bolt down brackets, CD with software, Installation guide, Network Management Card, Power modules ship installed, Smart UPS signalling RS-232 cable, Start-Up Service, User Manual
*Box quantity refers to the number of units contained in this product's outer packaging. It does not refer to the number of products purchased for the quoted unit price unless otherwise stated.
APC G35T10KH1B2S MGE Galaxy 3500 10kVA 400V
- Brand: APC
- Product Code: APC G35T10KH1B2S MGE Gala
- Availability: In Stock Ships in 1-2 days
Are you a VAR / Distributor?
Up to 15% Commission.
No MOQs. No Signup Fees.
Portable Server Room Diagnostic Sensor Toolkit
Despite advances in CFD software and pre-deployment simulations of data center environments. The majority of server rooms, remote sites and data centers are not designed to handle ever increasing loads and the heat generated by that increased activity.
WIRELESS WORKFLOW enables early diagnostics of any server room or data center facility. Detecting problems arising from under or over cooling, hot air re-circulation in IT rack space and air delivery resulting in high or low air pressure in raised floors and dropped ceiling plenums.Read the full article
Diagnosing server room temperature problems
Diagnose temperature differentials, pressure differentials and more...
AVTECH Room Alert 12E - Sensor Monitoring
Monitor temperature, humidity, power, room access and more...
AKCP SP2+ Temperature Monitoring
SP2+ monitors and logs temperature, humidity and more. SNMPv3 compliant, encrypted email and more...
Smart Cooling for Data Centers
Keeping temperatures in ASHRAE safe thermal envelopes.
AKCP SP2+ Temperature Sensor for Server Rooms
Front and rear thermal mapping for any server cabinet.
Monitor and manage server room environmental and security conditions over an IP network.