APC Smart-UPS On-Line,8000 Watts /8000 VA,Input 230V, 400V 3PH /Output 230V, Interface Port Contact Closure, RJ-45 10/100 Base-T, RJ-45 Serial, Smart-Slot, USB, Extended runtime model
LCD graphics display
Text and mimic diagrams that display modes of operation, system parameters and alarms.
10/100 BaseT Connection
Connect the device to a network using a 10 or 100 BaseT connection
Patent-pending operating mode that bypasses unused electrical components in good power conditions to achieve very high operating efficiency without sacrificing any protection.
Battery failure notification
Provides early-warning fault analysis on batteries enabling timely preventive maintenance
Automatic internal bypass
Supplies utility power to the connected loads in the event of a UPS power overload or fault.
Allows additional run time to be quickly added as needed.
Intelligent battery management
Maximizes battery performance, life, and reliability through intelligent, precision charging.
Ensures clean, uninterrupted power to protected equipment while batteries are being replaced
Automatic restart of loads after UPS shutdown
Automatically starts up the connected equipment upon the return of utility power.
Temperature-compensated battery charging
Prolongs battery life by regulating the charge voltage according to battery temperature.
Provides remote power management of the UPS over the network.
InfraStruXure Manager Compatible
Enables centralized management via the APC InfraStruXure Manager.
Customize UPS capabilities with management cards.
LED status indicators
Quickly understand unit and power status with visual indicators.
Provides management of the UPS via a serial port.
Plug-and-Play external batteries
Ensures clean, uninterrupted power to the loads when adding extra runtime to the UPS.
Protects the initial investment in the UPS when migrating from tower to rack-mount environment.
Flash upgradeable firmware
Install maintenance releases of firmware remotely using FTP.
Increases availability by allowing a trained user to perform upgrades and replacements of the batteries reducing Mean Time to Repair (MTTR)
Periodic battery self-test ensures early detection of a battery that needs to be replaced.
Predicitive failure notification
Provides early-warning fault analysis ensuring proactive component replacement.
Disconnected battery notification
Warns when a battery is not available to provide backup power.
Provides notification of changing utility power and UPS power conditions
Frequency and voltage regulation
Gives higher application availability by correcting poor frequency and voltage conditions without using the battery.
Protects connected loads from surges, spikes, lightning, and other power disturbances.
Input power factor correction
Minimizes installation costs by enabling the use of smaller generators and cabling.
Ensures clean, uninterrupted power to protected equipment when generator power is used.
Provides temporary battery power when the utility power is out.
Resettable circuit breaker
Easy recovery from overloads; no need to replace a fuse.
Ensures the product has been tested and approved to work safely with the connected service provider equipment and within the specified environment.
|Output Power Capacity|| |
8000 Watts / 8000 VA
|Max Configurable Power|| |
8000 Watts / 8000 VA
|Nominal Output Voltage||230V|
|Output Voltage Distortion||Less than 3%|
|Output Frequency (sync to mains)||50/60Hz +/- 3 Hz|
|Other Output Voltages||220, 240|
|Crest Factor||3 : 1|
|Topology||Double Conversion Online|
|Waveform Type||Sine wave|
|Output Connections||(1) Hard Wire 3-wire (H N + G) |
(6) IEC 320 C13
(4) IEC 320 C19
(3) IEC Jumpers
|Bypass||Internal Bypass (Automatic and Manual)|
|Nominal Input Voltage||230V, 400V 3PH|
|Input Frequency||45 - 65 Hz (auto sensing)|
|Input Connections||Hard Wire 3 wire (1PH+N+G) |
Hard Wire 5-wire (3PH + N + G)
|Other Input Voltages|| |
220, 240, 380, 415
|Batteries & Runtime|
|Battery Type||Maintenance-free sealed Lead-Acid battery with suspended electrolyte : leakproof|
|Typical recharge time||1.50 hour(s)|
|Extended Run Options||APC Smart-UPS SRT 8000VA 230V|
|Communications & Management|
|Interface Port(s)||Contact Closure, RJ-45 10/100 Base-T, RJ-45 Serial, Smart-Slot, USB|
|Available SmartSlot™ Interface Quantity||1|
|Control panel||Multi-function LCD status and control console|
|Audible Alarm||Audible and visible alarms prioritized by severity|
|Emergency Power Off (EPO)||Yes|
|Surge Protection and Filtering|
|Surge energy rating||480 Joules|
|Maximum Height||432.00 mm|
|Maximum Width||263.00 mm|
|Maximum Depth||715.00 mm|
|Net Weight||111.82 KG|
|Shipping Weight||126.82 KG|
|Shipping Height|| |
|Shipping Width||600.00 mm|
|Shipping Depth||1000.00 mm|
|Units per Pallet||1.00|
|Operating Environment||0 - 40 °C|
|Operating Relative Humidity||0 - 95% no%|
|Operating Elevation||0-900 meters|
|Storage Temperature||-15 - 45 °C|
|Storage Relative Humidity||0 - 95% no%|
|Storage Elevation||0-4500 meters|
|Audible noise at 1 meter from surface of unit||55.00 dBA|
|Online Thermal Dissipation||1497.00 BTU/hr|
|Protection Class||IP 20|
|Regulatory Approvals||CE, CE Mark|
|Standard Warranty||3 years repair or replace (excluding battery) and 2 years for battery|
|Sustainable Offer Status|
|REACH||REACH: Contains No SVHCs|
Includes: CD with software, Documentation CD, Installation guide, Temperature Probe, USB cable, Warranty card
*Box quantity refers to the number of units contained in this product's outer packaging. It does not refer to the number of products purchased for the quoted unit price unless otherwise stated.
APC SRT8KXLI Smart-UPS SRT 8000VA 230V
- Brand: APC
- Product Code: APC SRT8KXLI Smart-UPS SR
- Availability: In Stock Ships in 1-2 days
Are you a VAR / Distributor?
Up to 15% Commission.
No MOQs. No Signup Fees.
Portable Server Room Diagnostic Sensor Toolkit
Despite advances in CFD software and pre-deployment simulations of data center environments. The majority of server rooms, remote sites and data centers are not designed to handle ever increasing loads and the heat generated by that increased activity.
WIRELESS WORKFLOW enables early diagnostics of any server room or data center facility. Detecting problems arising from under or over cooling, hot air re-circulation in IT rack space and air delivery resulting in high or low air pressure in raised floors and dropped ceiling plenums.Read the full article
Diagnosing server room temperature problems
Diagnose temperature differentials, pressure differentials and more...
AVTECH Room Alert 12E - Sensor Monitoring
Monitor temperature, humidity, power, room access and more...
AKCP SP2+ Temperature Monitoring
SP2+ monitors and logs temperature, humidity and more. SNMPv3 compliant, encrypted email and more...
Smart Cooling for Data Centers
Keeping temperatures in ASHRAE safe thermal envelopes.
AKCP SP2+ Temperature Sensor for Server Rooms
Front and rear thermal mapping for any server cabinet.
Monitor and manage server room environmental and security conditions over an IP network.